气源处理器使用的注意事项

发布时间：2015年07月08日

气源处理器使用的注意事项

Cautions in Application of F.R.L Equipment

一、安装注意事项:(cautions in installation)

 ●气源处理器安装时过滤器、过滤减压阀、油雾器必须垂直安装，水杯向下,减压阀调压旋钮向下,且气体流动方向必须按壳体上箭头所示方向。

 ●安装时请考虑一定的安装与维护空间(如过滤器的安装高度以能卸下水杯为准),气源处理器避免安装在有较强振动的环境中,以维护压力表精度及连接件强度。

●尽量避免安装在阳光直射的场合。

●Clean the pipes before installation of pneumatic components  associated，Remove dust、oil、debris、etc.to prevent the fragments of sealing material mix。

●When installed，  the filter、filter regulator and lubricator must be vertically, the cup down, the knob of regulator down, and the gas flow direction must be consistent with the arrow on valve body。

●Before installation, please set some space for installation and maintenance (such as the height of filters mounting ，to be able to remove the cup)。FRL should be avoid installed in a strong vibration environment ，to protect the accuracy of pressure gauge and the strength of the connection。

●Avoid to installation in sunshine point-blank  occasion。

二、使用时注意事项:(Cautions in usage)

●过滤器应定期清洗滤芯，否则经过过滤器后系统压力降将会增大。滤芯与杯子请用家庭用中性清洗剂清洗，然后用清水漂净。

●请根据使用环境和气压系统要求选择合理的过滤器大小及排水方式。

●水杯与油杯材质为聚碳酸酯，应避免与四氯化碳、酸类、碱类、苯胺、煤油和其它对聚碳酸脂起化学反应的化学物品。

●确认过滤器及过滤减压阀杯子或杯子护罩正确到位后，方可开启压力，在加压状态下切勿旋转杯子及其护罩 。

●过滤减压阀（W型）、减压阀（R型）使用时将调压旋钮拔出调至使用压力，调完后将调压旋钮推入（止旋）。根据使用情况选择相应的压力表，方型压力表和单向阀板组件可以进行互换。

●油雾器可在不停气情况下加油。请将油杯内油量保持在油量上限与下限范围内。L3000、L4000旋开注油塞，从注油塞口处加油。L1000、L2000将排气塞旋开，排除残余气体，卸下杯子直接从杯口加油；然后将油杯旋入阀体，再将排气塞拧紧。(油雾器使用ISO VG32或同级润滑油)

●油雾器滴液流量的调节，用一字型调节工装逆时针调节调油件滴液流量增加，顺时针调节调油件滴液流量减少，调节过程中不能用力过大。

 ●残压排出:排出杯子内的压力(F.W用放水旋塞、L1000、2000系列用排气塞排气、L3000、4000  系列用注油塞排气）后，请确认压力是否完全排除。

 ●气源处理器中密封圈使用寿命3-5年，使用到期请进行更换。

●The filter should be cleaned regularly, otherwise the system pressure drop will increase. When cleaning the filter or the cup, use a neutral household detergent, then rinse with water.

●According to the work environment and the requirements of pneumatic system to select the appropriate filter such as size or drainage patterns。

●As the cup is made of polycarbonate, should avoid contact with carbon tetrachloride, acids, bases, aniline, kerosene and other chemicals be easy to reaction with polycarbonate.

●Before the open,make sure the cup or cup shield of the filter and filter regulator in right place。 Under the pressure, do not rotate the cup or shield.

●When using, please pull out the regulator knob such as filter regulator (W type) or regulator (R type), Adjusted to the desired pressure，Then push the regulator knob to prevent rotation. According to select the appropriate use of pressure gauge. Square gauge and check valve plate assembly can be interchanged.

●Please maintain the oil in the cup in the upper and lower limits. You can add oil in the case non-stop gas 。

1 for the L3000, L4000 series, first unscrew the fill plug, and add oil through the fill plug hole.

2 for L1000, L2000 series, first unscrew the vent plug, then remove the cup, add the oil directly to the cup; then screwed the cup into the valve, then tighten the vent plug. (Lubricator with oil ISO VG32 or Same level )

●Lubricator drip flow regulation: we can use a screwdriver to adjust the regulator. Counterclockwise, drip flow increases; clockwise, drip flow reduction. Note: The adjustment process can not be too hard.

●Discharge of residual pressure:The pressure within the exhaust cup (FW with drain cocks, L1000、2000 series with the exhaust vent plug, L3000、4000 series with the fill plug exhaust), make sure the pressure is completely ruled out.

●The normal life of the product seal is five years, to be replaced periodically.